Climbing Panels – Indoor Climbing Walls for Kids (Rectangular)

Panel size: 1168 × 584 mm

Finished depth: Approximately 36 mm, excluding rear hardware

Front panel: 18 mm high-grade birch plywood

Rear backing frame: 18 mm high-grade birch plywood

Climbing hold holes: 18 pre-drilled holes with pre-installed T-nuts

Maximum user weight: 70 kg per panel

Use: Indoor bouldering and free climbing only

Maximum wall height: 3 metres unless specifically assessed by an appropriately qualified professional

Orientation: Horizontal or vertical

Recommended climbing holds: Approximately 10 holds per rectangular panel

Included: 1 climbing panel, 6 × 100 mm 14G batten screws, 6 screw-cap covers and Ako Playrooms Installation & Safety Guide

Climbing holds: Sold separately

Fall-protection surfacing: Sold separately

Engineering: Standard timber-framed installation detail reviewed and certified by a structural engineer, subject to the stated engineering scope, assumptions and installation requirements

Climbing Panels must only be installed onto a flat, structurally sound supporting wall capable of supporting the panel, user and forces generated during climbing.

For installation to timber framing, each panel must span at least two separate structural studs or nogs. Timber framing must be a minimum of 90 × 45 mm.

Use a minimum of four structural fixing points per panel, with two fixing points into each of at least two separate studs or nogs. Fixings must pass through the front panel and rear backing frame and into the centre of the structural framing.

Do not fix the panels into plasterboard, wall lining, brick or brick veneer alone.

The supplied 100 mm 14G batten screws are intended for suitable timber-framed installations meeting the requirements of the Ako Playrooms Installation & Safety Guide. The installer must confirm that the supplied screws and proposed fixing locations are appropriate for the actual wall construction and condition.

For concrete, concrete block, steel framing or other wall construction, specialised fixings may be required and are not covered by the standard timber-framed installation detail. An appropriately qualified professional must determine the suitable fixing method.

The purchaser and installer are responsible for identifying the existing wall construction and confirming that the supporting structure is sound, free from defects and suitable for climbing loads before installation.

If the structure, framing, substrate or fixing method cannot be confidently established, installation must not proceed until it has been assessed by an appropriately qualified builder, installer or structural professional.

For overhanging walls, ceilings or installation configurations outside the standard vertical-wall installation described in the Ako Playrooms Installation Guide, obtain specific professional advice before installation.

View the installation guide.

• Adult supervision is required whenever children are using the climbing wall.
• For indoor bouldering and free climbing only. Do not attach ropes, anchors, belay systems, swings or other suspension equipment to the climbing panels.
• Only one climber should use each climbing route at a time. Keep other children and observers clear of the fall area while someone is climbing.
• Do not jump, swing or deliberately drop from the panels.
• Maximum user weight is 70 kg per panel.
• Do not modify the panels, remove T-nuts, drill additional holes or use incompatible climbing holds or fixings.
• Use appropriate fall-protection surfacing beneath and around the full climbing area. Fall protection must be selected to suit the installed climbing height and must prevent the user from bottoming out onto the underlying floor.
• Keep the fall area free from furniture, toys, sharp edges and other obstacles.
• Do not install climbing panels over live electrical outlets. Any electrical services within the proposed installation area must be appropriately dealt with by a qualified person before installation.
• Inspect the panels, climbing holds and all fixings before use. Carry out a more thorough inspection at least every 30 days, or more frequently where the wall receives heavy use.
• Check for loose holds or fixings, movement between the panel and wall, splintering, delamination, deterioration and damaged or stripped T-nuts.
• Stop use immediately if any part of the climbing wall, fixing system or fall protection becomes loose, damaged or deteriorated. Do not resume use until the issue has been properly rectified.
• Installation, use, inspection and maintenance must follow the current Ako Playrooms Rectangular Climbing Panel Installation & Safety Guide.

ENGINEERING & SITE CONDITIONS

The standard timber-framed installation detail for Ako Playrooms Rectangular Climbing Panels has been reviewed and certified by a structural engineer.

The engineering certification applies only within the scope, construction, materials, fixings, framing requirements, load limits, assumptions and jurisdiction stated in the applicable engineering documentation.

The engineering certification does not certify the condition or structural capacity of an individual customer's existing wall, framing or completed installation.

The installer must verify the actual wall construction, structural framing, fixing locations and condition of the supporting structure before installation and confirm that the completed installation complies with the Ako Playrooms Installation & Safety Guide and applicable engineering requirements.

Installations outside the certified standard installation detail require separate assessment by an appropriately qualified professional.

• All products come with a 6-month warranty covering manufacturing defects.
  
• Photo evidence of any issue will be required before a remedy is offered. Ako Playrooms will determine the appropriate solution, which may include repair or replacement.
  
• This warranty does not cover:
  1.General wear and tear
  2.Improper use or misuse
  3.Damage caused during self-installation or incorrect installation
  4.Alterations or modifications to the product
  
  
• Ako Playrooms reserves the right to assess claims on a case-by-case basis.
  

See our Warranty Policy for more.

We are currently shipping to New Zealand and Australia. This product is made to order. Ships in 4 to 6 weeks. Ships directly from the manufacturer. Refer to shipping policy.

This product must be installed into a compliant timber framing system by a qualified professional or competent DIY installer.

Panels must be fixed to timber studs no smaller than 90 × 45 mm, using 4 batten screws per panel (2 at the top and 2 at the bottom) across 2 separate studs.

Installation into plasterboard, hollow cavities, or unsupported substrates is strictly prohibited and may result in serious injury or structural failure.

The stated Working Load Limit (WLL) of 70 kg applies only when panels are correctly installed into structurally sound timber framing.

Liability: Ako Playrooms accepts no responsibility for injuries, accidents, or damage resulting from incorrect installation, overloading, misuse, or failure to follow safety instructions.

Regular inspection and maintenance of all fixings and climbing holds is required.

By purchasing or installing this product, you acknowledge and accept full responsibility for safe installation and use.

The use of fall protection (e.g., crash mats) is strongly recommended.